View ALT6526P9_8396579.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

alt6526 multi-band lte/cdma/wcdma/hspa power amplifer data sheet - rev 2.5 22 pin 5 mm x 7 mm x 0.9 mm surface mount module figure 1: block diagram features ? lte, wcdma/hspa & cdma/evdo applications ? high output power ? +27.3 dbm in lte ? +28.6 dbm in wcdma (r99) ? +27.5 dbm in cdma (rc1) ? high effciency ? 40% in high power mode (wcdma mode) ? low profle 5 mm x 7 mm x 0.9 mm package ? 2 input ports, 5 output ports, all matched to 50 impedance ? integrated voltage regulator ? built-in directional coupler ? internal dc block on in/out rf ports ? low leakage in shutdown mode ? esd protection on all pins ? rohs-compliant package, msl-3, 260c applications ? lte, wcdma/hspa handsets and data devices operating in umts bands 1, 2, 3, 4, 5, 8, 9,10, 18, 19, 20, 25, and 26 ? cdma/ev-do handsets and data devices operating in band class 0, 1, 4, 6, 8, 10, 14g and 15 product description the alt6526 power amplifer module is designed for 3g/4g handsets, smartphones, modems and modules operating in lte, wcdma/hspa and cdma/evdo modes. the module includes separate ingap hbt amplifer chains - one to support 850/900 bands, the other for 1700/1900/2100mhz bands. an innovative design allows the module to switch output among as many as 5 different frequency bands. both the input and output rf ports are internally matched to 50 . the alt6526 offers improved effciency and low quiescent current, and includes integrated daisy chained couplers to simplify board design and layout. al t6526 07/2013
2 figure 2: pinout (x-ray top view) table 1: pin description na me d escri pt ion pi np in na me descri pt io n 1 rf in_hi rf input for 1700/1800/1900 mhz bands 12 rf out_900 rf ou tp ut for 900 mhz band 2 gnd ground 13 rf out_850 rf output for 850 mhz band 3v batt battery voltage 14 gnd ground 4v cc1 supply voltage 15 v cc supply voltag e 5v en_hi enable voltage for high bands 16 v cc su pply vo lt age 6v band0 low band select voltag e 17 v cc su pply vo lt age 7v band1 high band select voltage 18 cpl _out coupler output por t 8v mode mode control voltage 19 gn d gro und 9v en_lo enable voltage for low bands 20 rf out_1900 rf output for 1900 mhz band 10 gnd grounds 21 rf out_1700 rf output for 1700 mhz band 11 rf in_lo rf input for 850/900 mhz bands 22 rf out_2100 rf output for 2100 mhz band rf out_ 2100 rf out_ 1700 rf in_h i gn d cp l out v en_hi v ba tt gn d 22 21 20 19 18 v cc1 rf out_ 1900 1 2 3 4 5 6 7 8 9 10 11 17 16 15 14 13 12 v cc v cc gn d rf out_ 850 v cc v ban d0 gn d v mo de v ban d1 v en _l o rf in_l o rf out _900 data sheet - rev 2.5 07/2013 alt6526
3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. pa ra me ter mi n ma x unit su pply vo ltage (v ba tt , v cc , v cc1 )0 +5 v co nt ro l vo ltages (v mo de , v ban d0 /1 )0 +3 .5 v en able vo ltages (v en_hi , v en_lo )0 +3 .5 v in pu t rf po we r (rf in_hi , rf in_lo )- +1 0d bm st or a ge te mp er at ur e- 40 +1 50 c table 3: dc operating parameters parameter min typ max unit comments supply voltage (v cc & v cc1 ) +0.7 +3.3 +4.35 v supply voltage (v batt ) +2.9 +3.3 +4.35 v control voltages (v mode , v band0/1 ) +1.35 0 +1.8 - +3.1 +0.4 v select high state select low state enable voltage (v en_hi , v en_lo ) +1.35 0 +1.8 - +3.1 +0.4 v select high state select low state mode control current - <0.1 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.1 0.12 ma through v en_hi , v en_lo band control current - <0.1 0.12 ma through v band0 or v band1 pins batt current - 2.3 5 ma through v batt pin, v mode = +1.8 v leakage current (total) - <5 11 a v batt = +4.5 v, v cc = +4.5 v, shutdown mode (all v batt & v cc pins) data sheet - rev 2.5 07/2013 alt6526
4 table 4: rf operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operations at 3.2 v or 105 8c, p out is derated by 0.6 db. (2) 3gpp ts 34.121-1, rec .8 table c 11.1.3 subtest 1. (3) lte waveform characteristics: up to 20 mhz bw, qpsk, rb = 18. parameter min typ max unit comments 2shudl)uhtxhfi - - - - - - 0 0%dq%&%& 0%dq 0%dq 0%dq%& 0%dq%& 0%dq%& wswh0 0 0 0 /0 0 0 0 /0 /0 /0 /0 0 /0 /0 0 0 0 /0 0 /0 0 /0 /0 /0 0 0 0 /0 0 /0 0 /0 /0 /0 - - - - - - - - - - - - - - - - - - - - dbm 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq 0%dq cdma output power &0&0 &0&/0 &0&0 &0&/0 &0&0 &0&/0 - - - - - - dbm %dq&odvv %dq&odvv %dq&odvv &dvhhpshdwh c -40 - 8c data sheet - rev 2.5 07/2013 alt6526
5 table 4a: electrical specifcations - band 1 (2100 mhz) lte operation (rb = 12, start = 0, qpsk) (+25 c, v batt = v cc = +3.3 v, v en_hi = +1.8 v, v band0 = v band1 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v cc v mode gain 25 - 9 28.5 19 13 32.5 - 16 db +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v e-utra at 10 mhz offset - - - -38 -41 -40 -34 - -34 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr1 at 7.5 mhz offset (1) - - - -39 -40 -41 -36 - -36 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr2 at 12 mhz offset - - - -60 -60 -60 -40 - -40 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v effciency (1) 30.5 - 36 3.5 - - % +27.4 dbm +9.6 dbm 3.3 v 3.3 v 0 v +1.8 v quiescent current - 40 - ma through v cc1 + v cc pins, v mode = 1.8 v noise in receive band - -135 - dbm/hz 2110 - 2170 mhz gps noise - -137 - dbm/hz p out 27.4 dbm ism noise - -145 - dbm/hz p out 27.4 dbm out of band gain rx band gps band ism band - - - g - 2.8 g - 2.4 g - 8 - - - db g = in-band gain harmonics 2f o 3f o , 4f o - - -42 -50 -30 -35 dbc input impedance - - 2:1 vswr suprious output level (all spurious outputs) - - -70 dbc see note 2. load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range coupling factor - 27.5 - db data sheet - rev 2.5 07/2013 alt6526
6 table 4b: electrical specifcations - band 1 (2100 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = +1.8 v, v band0 = v band1 = 0 v, v en_lo = 0 v) table 4c: electrical specifcations - band class 6 (2100 mhz) cdma 2000 operation (rc-1 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = +1.8 v, v band0 = v band1 = 0 v, v en_lo = 0 v) notes (applicable to tables 4a, 4b and 4c): (1) aclr and effciency measured at 1950 mhz. (2) p out < +28.7 dbm, in-band load vswr < 5:1, out-of-band load vswr < 10:1. applies over all operating conditions. pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ad ja ce nt ch an ne l po we r (1 ) at 1. 25 mh z o ffs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 1 -5 1 -4 6. 5 -4 6.5 db c + 27. 7 db m +9 .6 db m 0 v 1. 8 v al te rn at e ch a nne l po we r (1 ) at 1. 98 mh z o ffs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 7 <- 60 -5 4 -5 4 db c + 27. 7 db m +9 .6 db m 0 v 1. 8 v pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ac lr 1 at 5 mh z o ffs et (1 ) - - -4 1 -4 0 -3 7 -3 7 db c + 28. 6 db m +1 0. 6 db m 0 v 1. 8 v ac lr 2 at 10 mh z o ffs et - - -5 5 <- 60 -4 8 -4 8 db c + 28. 6 db m +1 0. 6 db m 0 v 1. 8 v e ffi ci en cy (1 ) 35 - 41 4 - - % + 28. 6 db m +1 0. 6 db m 0 v 1. 8 v data sheet - rev 2.5 07/2013 alt6526
7 table 5a: electrical specifcations - band 2/25 (1900 mhz) lte operation (rb = 12, start = 0, qpsk) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = +1.8 v, v band0 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v cc v mode gain 25.5 - 10 28.5 20 13.5 32 - 16.5 db +27.7 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v e-utra at 10 mhz offset - - - -38 -42 -40 -34 - -34 dbc +27.7 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr1 at 7.5 mhz offset (1) - - - -39 -43 -41 -36 - -36 dbc +27.7 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr2 at 12 mhz offset - - - -60 -60 -60 -40 - -40 dbc +27.7 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v effciency (1) 30.5 - 36 3.5 - - % +27.7 dbm +9.6 dbm 3.3 v 3.3 v 0 v +1.8 v quiescent current - 40 - ma through v cc1 + v cc pins, v mode = 1.8 v noise in receive band - -135 - dbm/hz 1930 - 1990 mhz gps noise - -137 - dbm/hz p out 27.7 dbm ism noise - -149 - dbm/hz p out 27.7 dbm out of band gain rx band gps band ism band - - - g - 0.5 g - 0.8 g - 8 - - - db g = in-band gain harmonics 2f o 3f o , 4f o - - -40 -46 -35 -35 dbc input impedance - - 2:1 vswr suprious output level (all spurious outputs) - - -70 dbc see note 2 load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range coupling factor - 29 - db data sheet - rev 2.5 07/2013 alt6526
8 table 5b: electrical specifcations - band 2/25 (1900 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = +1.8 v, v band0 = 0 v, v en_lo = 0 v) table 5c: electrical specifcations - band class 1 (1900 mhz) cdma2000 operation (rc-1 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = +1.8 v, v band0 = 0 v, v en_lo = 0 v) notes (applicable to tables 5a, 5b and 5c): (1) aclr and effciency measured at 1882.5 mhz. (2) pout 27.7 dbm, in-band load vswr < 5:1, out-of-band load vswr 10:1. applies over all operating conditions pa ra me te r mi n ty p ma x uni t co mme nt s p ou t v mo de ad ja ce nt ch an ne l po we r (1 ) at 1. 25 mh z of fs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 2 -5 1 -4 6. 5 -4 6.5 dbc +2 8.1 dbm +9 .6 db m 0 v 1. 8 v al te rn at e ch an ne l po we r (1 ) at 1. 98 mh z of fs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 7 <-60 -5 4 -5 4 db c + 28. 1 db m +9 .6 db m 0 v 1. 8 v pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ac lr 1 at 5 mh z o ffs et (1 ) - - -4 1 -4 0 -3 7 -3 7 db c + 29.0 db m +10.6 db m 0 v 1. 8 v ac lr 2 at 10 mh z o ffs et - - -5 3 <- 60 -4 8 -4 8 db c + 29.0 db m +10.6 db m 0 v 1. 8 v e ffi ci en cy (1 ) 35 - 40 4 - - % + 29.0 db m +10.6 db m 0 v 1. 8 v data sheet - rev 2.5 07/2013 alt6526
9 table 6a: electrical specifcations - band 3/4 (1700 mhz) lte operation (rb = 12, start = 0, qpsk) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band0 = +1.8 v, v band1 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v cc v mode gain 26 - 9 28.5 18 13 32.5 - 16 db +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v e-utra at 10 mhz offset - - - -38 -39 -40 -34 - -34 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr1 at 7.5 mhz offset (1) - - - -39 -40 -41 -36 - -36 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr2 at 12 mhz offset - - - -60 -60 -60 -40 - -40 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v effciency (1) 30.5 - 36 3.5 - - % +27.4 dbm +9.6 dbm 3.3 v 3.3 v 0 v +1.8 v quiescent current - 40 - ma through v cc1 + v cc2 pins, v mode = 1.8 v noise in receive band - - -135 -142 - - dbm/hz 1805 - 1880 mhz 2110 - 2155 mhz gps noise - -134 - dbm/hz p out 27.4 dbm ism noise - -149 - dbm/hz p out 27.4 dbm out of band gain rx band (b3) rx band (b4) gps band ism band - - - - g g - 2 g - 1 g - 10 - - - - db g = in-band gain harmonics 2f o 3f o , 4f o - - -42 -55 -30 -35 dbc p out +27.4 dbm input impedance - 2:1 - vswr suprious output level (all spurious outputs) - - -70 dbc see note 2. load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range coupling factor - 28.5 - db data sheet - rev 2.5 07/2013 alt6526
10 table 6b: electrical specifcations - band 3/4 (1700 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band0 = +1.8 v, v band1 = 0 v, v en_lo = 0 v) table 6c: electrical specifcations - band class 8 (1700 mhz) cdma operation (rc-1 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band0 = +1.8 v, v band1 = 0 v, v en_lo = 0 v) notes (applicable to tables 6a, 6b and 6c): (1) aclr and effciency measured at 1747.5 mhz. (2) p out < +28.6 dbm; in-band load vswr < 5:1; out-of-band load vswr < 10:1; applies over all operating conditions. pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ad ja ce nt ch an ne l po we r (1 ) at 1. 25 mh z o ffs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 2 -5 2 -4 6. 5 -4 6.5 db c + 27.7 db m +9 .6 db m 0 v 1. 8 v al te rn at e ch a nne l po we r (1 ) at 1. 98 mh z o ffs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 7 <- 60 -5 4 -5 4 db c + 27. 7 db m +9 .6 db m 0 v 1. 8 v pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ac lr 1 at 5 mh z o ffs et (1 ) - - -4 1 -4 0 -3 7 -3 7 db c + 28.6 db m +10.6 db m 0 v 1. 8 v ac lr 2 at 10 mh z o ffs et - - -5 5 <- 60 -4 8 -4 8 db c + 28. 6 db m +1 0. 6 db m 0 v 1. 8 v e ffi ci en cy (1 ) 35 - 41 4 - - % + 28. 6 db m +1 0. 6 db m 0 v 1. 8 v data sheet - rev 2.5 07/2013 alt6526
11 table 7a: electrical specifcations - band 5 (850 mhz) lte operation (rb = 12, start = 0, qpsk) (+25 c, v batt = v cc = +3.3 v, v en_hi = 0 v, v band1 = v band0 = +1.8 v, v en_lo = 1.8 v ) parameter min typ max unit comments p out v cc v mode gain 25.5 - 10 28 17 13 31.5 - 16.5 db +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v e-utra at 10 mhz offset - - - -38 -41 -40 -34 - -34 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr1 at 7.5 mhz offset (1) - - - -39 -42 -40 -36 - -36 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr2 at 12 mhz offset - - - -60 -60 -60 -40 - -40 dbc +27.4 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v effciency (1) 30.5 - 35 4 - - % +27.4 dbm +9.6 dbm 3.3 v 3.3 v 0 v +1.8 v quiescent current - 35 - ma through v cc1 + v cc pins, v mode = 1.8 v noise in receive band - -132 -136 - - dbm/hz 741 - 821 mhz (2) 862 - 894 mhz gps noise - -158 - dbm/hz p out 27.4 dbm ism noise - -160 - dbm/hz p out 27.4 dbm out of band gain rx band gps band ism band - - - g - 0.7 g - 40 g - 50 - - - db g = in-band gain harmonics 2f o 3f o , 4f o - - -44 -50 -35 -35 dbc p out +27.4 dbm input impedance - 2:1 - vswr suprious output level (all spurious outputs) - - -70 dbc see note 3. load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range coupling factor - 27.5 - db data sheet - rev 2.5 07/2013 alt6526
12 table 7c: electrical specifcations - band class 0/10 (850 mhz) cdma2000 operation (rc-1 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = 0 v, v band1 = v band0 = +1.8 v, v en_lo = 1.8 v ) notes (applicable to tables 7a, 7b and 7c): (1) aclr and effciency measured at 833 mhz. (2) ts36.101, table 7.3.1-2 (3) p out < +28.6 dbm, in-band load vswr < 5:1, out-of-band load vswr < 10:1. applies over all operating conditions. table 7b: electrical specifcations - band 5 (850 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = 0 v, v band1 = v band0 = +1.8 v, v en_lo = 1.8 v ) pa ra me te r mi n ty p ma x uni t co mme nt s p ou t v mo de ad ja ce nt ch an ne l po we r (1 ) at 885kh z of fs et pr im ar y ch a nne l bw = 1. 23 mh z - - -5 1 -5 0 -4 6. 5 -4 6.5 dbc + 27. 5 db m +9 .6 db m 0 v 1. 8 v al te rn at e ch an ne l po we r (1 ) at 1. 98 mh z of fs et pr im ar y ch a nne l bw = 1. 23 mh z - - -60 <-63 -5 7 -5 7 db c +2 7. 5 db m +9 .6 db m 0 v 1. 8 v pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ac lr 1 at 5 mh z o ffs et (1 ) - - -4 1 -4 1 -3 7 -3 7 db c + 28. 6 db m +10.6 db m 0 v 1. 8 v ac lr 2 at 10 mh z o ffs et - - -5 7 <- 60 -4 8 -4 8 db c + 28. 6 db m +10.6 db m 0 v 1. 8 v e ffi ci en cy (1 ) 34 - 39 4 - - % + 28. 6 db m +10.6 db m 0 v 1. 8 v data sheet - rev 2.5 07/2013 alt6526
13 table 8a: electrical specifcations - band 8 (900 mhz) lte operation (rb = 12, start = 0, qpsk) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = v band0 = 0 v, v en_lo = 1.8 v) parameter min typ max unit comments p out v cc v mode gain 25.5 - 9.5 28 17 12.5 31.5 - 16 db +27.5 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v e-utra at 10 mhz offset - - - -38 -39 -39 -34 - -34 dbc +27.5 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr1 at 7.5 mhz offset (1) - - - -39 -40 -41 -36 - -36 dbc +27.5 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v aclr2 at 12 mhz offset - - - -60 -60 -60 -40 - -40 dbc +27.5 dbm +3 dbm +9.6 dbm 3.3 v 0.7 v 3.3 v 0 v 0 v +1.8 v effciency (1) 30.5 - 35 4 - - % +27.5 dbm +9.6 dbm 3.3 v 3.3 v 0 v +1.8 v quiescent current - 35 - ma through v cc1 + v cc pins, v mode = 1.8 v noise in receive band - -136 - dbm/hz 925 - 960 mhz gps noise - -160 - dbm/hz p out 27.5 dbm ism noise - -160 - dbm/hz p out 27.5 dbm out of band gain rx band gps band ism band - - - g - 0.5 g - 30 g - 50 - - - db g = in-band gain harmonics 2f o 3f o , 4f o - - -42 -50 -30 -35 dbc p out +27.5 dbm input impedance - - 2:1 vswr suprious output level (all spurious outputs) - - -70 dbc see note 2. load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range coupling factor - 27.5 - db data sheet - rev 2.5 07/2013 alt6526
14 table 8b: electrical specifcations - band 8 (900 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = v band0 = 0 v, v en_lo = 1.8 v) notes (applicable to tables 8a and 8b): (1) aclr and effciency measured at 897.5 mhz. (2) p out < +28.7 dbm, in-band load vswr < 5:1, out-of-band load vswr < 10:1. applies over all operating conditions. pa ra me ter mi n ty p ma x unit co mme nt s p out v mo de ac lr 1 at 5 mh z o ffs et (1 ) - - -4 1 -4 0 -3 7 -3 7 db c + 28.7 db m +9.6 db m 0 v 1. 8 v ac lr 2 at 10 mh z o ffs et - - -5 6 <- 60 -4 8 -4 8 db c + 28.7 db m +9.6 db m 0 v 1. 8 v e ffi ci en cy (1 ) 34 - 39 - - % + 28.7 db m +9.6 db m 0 v 1. 8 v 4 data sheet - rev 2.5 07/2013 alt6526
15 table 9: logic interface specifcations figure 3: evaluation board logic programming application information rf ou t_ 2100 rf ou t_ 1700 rf in _h i gn d cp l ou t v batt gn d 22 21 20 19 18 g nd sl ug rf ou t_ 1900 1 2 3 4 5 6 7 8 9 10 11 17 16 15 14 13 12 v cc v cc gn d rf ou t_ 850 v cc v band 0 gn d v mo de v band 1 v en _l o rf in _l o rf ou t_ 900 68p f c1 2.2u f c3 0.01f c2 68p f c5 v bat t v cc1 v cc v cc1 v en _h i c6 0.01f 2.2f 2.2f c7 c4 mo de of o per at ion v en _h i v en _l o v ba nd0 v ba nd1 v mo de um ts ba nd 1, cd ma bc 6h ig hl ow low low x um ts ba nd 2 & 25 cdma bc 1, 6, 14g hi gh lowl ow hi gh x hi gh lowh ig h low x lowh ig hh ig hh ig hx um ts ba nd 8l ow hi gh low low x st an dby mo de lowl ow xx x sh ut down mo de lowl ow low low x hi gh po we r mo de (h pm )x xxx low low po we r mo de (l pm )x xx xh ig h umts band 3, 4, 9, 10 cdma bc 4, 8, 15 umts band 5, 18, 19, 20, 26 bc 0, 10 data sheet - rev 2.5 07/2013 alt6526
16 figure 5: branding specifcation figure 4: package outline - 22 pin 5 mm x 7 mm x 0.9 mm surface mount module package outline al t6526 llllln n yy wwcc anadigics logo pin 1 identifie r pa rt number date co de yy = ye ar ww= wo rk we ek lo t number co untr y co de (c c) data sheet - rev 2.5 07/2013 alt6526
17 ordering information o rder num be r temp er at ure ra ng e pa ckage descri pti on co mp on ent pa cka gin g alt6 526p 8- 40 o c to +1 05 o c ro hs co mp li an t 22 pi n 5 mm x 7 mm x 0.9 mm su rf ac e mo unt m odu le t ape an d re el , 2500 pi ec es per r eel alt6 526p 9- 40 o c to +1 05 o c ro hs co mp li an t 22 pi n 5 mm x 7 mm x 0.9 mm su rf ac e mo unt m odu le pa rt ia l t ape an d re el warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. import ant notice anadigics 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.5 07/2013 alt6526

▲Up To Search▲

Price & Availability of ALT6526P9

	To Download ALT6526P9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .